Natural CO2® Spin/Vac Technology
We prevent the growth of mold with our exclusive air duct cleaning system.
Schedule Today!
(616) 329-3741
(616) 329-3741
"GREENCO2 helps to eliminate the full range of indoor pollutants, including viruses, airborne chemicals, allergens, bacteria and mold."
Cleaning of all registers, supply and return duct work, main trunk,
and furnace. Also blower, evaporator coil and other accessible components.
Bathroom Exhaust Vents (optional).
Water Heater (optional).
Free Fogging of all duct work with a bacterial inhibitor.
Free Room Vacuuming.
Free Air Freshener with each service.
|
|
|
GREENCO2 Air Duct Cleaning and Furnace Cleaning Service in Grand Rapids, Kalamazoo and many cities in Michigan cleans your air ventilation system and all associated duct work. This includes all return and supply registers, furnace and the main trunk lines. Also blower, evaporator coil and other accessible components.
GREENCO2 air duct cleaning cleans every part of your ventilation system.
Don’t just trust any company out there for air duct cleaning.
Many competitors use inferior equipment that don't do as good of a job.
Our Natural CO2 Spin/Vac Air Duct Cleaning System (2016)
is exclusive and only from GREENCO2.
GREENCO2 air duct cleaning cleans every part of your ventilation system.
Don’t just trust any company out there for air duct cleaning.
Many competitors use inferior equipment that don't do as good of a job.
Our Natural CO2 Spin/Vac Air Duct Cleaning System (2016)
is exclusive and only from GREENCO2.
|
|
|
|
Dirty Register with Mold Cleaned Mold and Register Dirty Duct with debris, soil and bacteria Air Duct Cleaned
Air Compressor Method: Negative Air Method
This type of method basically cuts a hole in your trunk line and hooks up a big, powerful vacuum. The company will use an air compressor to blow air while the big, powerful vacuum sucks. Negative air is not suited for residential & light commercial ductwork because it will only remove the “loose” debris from the duct. Anything stuck on the duct wall will remain. Some companies will add “Air Whips” to the air compressor to randomly knock off a little bit of dirt from the duct wall. However, the “Random” whip works inefficiently and most of the stuck on dust, dirt, pollen, etc. remains stuck on the duct wall.
Other Rotary Brush Systems:
Some companies out there have the right idea with rotary brush cleaning, however, have the wrong equipment to do the job right. Most companies out there that use brushes to clean the duct work have systems that attach the brush directly onto the vacuum hose. The cleaning technician will feed the vacuum hose/brush combination into the duct work. The problem with this type of setup is that a fat vacuum hose with a brush on the end cannot maneuver throughout the duct work to remove the contaminants. A home or business has twists and turns throughout the duct work. Because of the brush attachment on the vacuum hose, this type of system cannot make the tight turns necessary to completely travel to the end of the duct. So, basically, the technician is cleaning just “some” of the duct!
Now comes GREENCO2 Patented Natural CO2 Spin/Vac Duct Cleaning System
services in Grand Rapids, MI and Yuma, Arizona
Our certified technicians use specially designed equipment with features & technology that improve the duct cleaning process. Our system contains the power of CO2 and its uniquely designed “angle pitched” brushes that strategically reverse sweep the contaminants back towards the cleaning technician.
These brushes also self-adjust to the size of the duct work (even rectangular duct work) to help
ensure the whole duct width is being cleaned. These brushes connect to a flexible cable that can “snake” its way through the twist and turns of duct work. Our separate vacuum hose follows behind. Thus, even where the vacuum hose stops, the brush/cable can continue to snake its way to the end of the duct work. The reverse sweeping action carries the contaminates back to the vacuum hose for extraction. The whole process is strategic & efficient.
Plus, because of our system’s maneuverability, we don’t have to cut holes into your duct work!
We enter through each and every vent location to clean all of the duct work.
This type of method basically cuts a hole in your trunk line and hooks up a big, powerful vacuum. The company will use an air compressor to blow air while the big, powerful vacuum sucks. Negative air is not suited for residential & light commercial ductwork because it will only remove the “loose” debris from the duct. Anything stuck on the duct wall will remain. Some companies will add “Air Whips” to the air compressor to randomly knock off a little bit of dirt from the duct wall. However, the “Random” whip works inefficiently and most of the stuck on dust, dirt, pollen, etc. remains stuck on the duct wall.
Other Rotary Brush Systems:
Some companies out there have the right idea with rotary brush cleaning, however, have the wrong equipment to do the job right. Most companies out there that use brushes to clean the duct work have systems that attach the brush directly onto the vacuum hose. The cleaning technician will feed the vacuum hose/brush combination into the duct work. The problem with this type of setup is that a fat vacuum hose with a brush on the end cannot maneuver throughout the duct work to remove the contaminants. A home or business has twists and turns throughout the duct work. Because of the brush attachment on the vacuum hose, this type of system cannot make the tight turns necessary to completely travel to the end of the duct. So, basically, the technician is cleaning just “some” of the duct!
Now comes GREENCO2 Patented Natural CO2 Spin/Vac Duct Cleaning System
services in Grand Rapids, MI and Yuma, Arizona
Our certified technicians use specially designed equipment with features & technology that improve the duct cleaning process. Our system contains the power of CO2 and its uniquely designed “angle pitched” brushes that strategically reverse sweep the contaminants back towards the cleaning technician.
These brushes also self-adjust to the size of the duct work (even rectangular duct work) to help
ensure the whole duct width is being cleaned. These brushes connect to a flexible cable that can “snake” its way through the twist and turns of duct work. Our separate vacuum hose follows behind. Thus, even where the vacuum hose stops, the brush/cable can continue to snake its way to the end of the duct work. The reverse sweeping action carries the contaminates back to the vacuum hose for extraction. The whole process is strategic & efficient.
Plus, because of our system’s maneuverability, we don’t have to cut holes into your duct work!
We enter through each and every vent location to clean all of the duct work.